For Research Use Only. Everything on this site is intended solely for laboratory, analytical, or institutional research — not for human or veterinary use, consumption, diagnosis, treatment, or prevention.

Analytical documentation guide

Counterions on a Peptide COA: Why TFA Changes the Weight

A COA can report purity above 99% and a content figure that looks lower than the label for the same lot. Neither number is wrong. They answer different questions, and the counterion is one quiet reason they differ.

4-minute readPublished by DAAVY Research

Scope

The short answer

A peptide’s charged groups are paired with counterions, most often trifluoroacetate (TFA) left over from cleavage and HPLC purification. The counterion has mass but does not show up in a standard HPLC purity result, so powder weight and peptide weight are not the same thing.

This guide describes analytical documentation for laboratory research materials. It makes no claims about use in people or animals and gives no dosing or preparation guidance.

What a counterion is

In solid form each charged group on a peptide is paired with an oppositely charged ion so the material is neutral. For the positively charged groups (the N-terminus and basic side chains such as lysine, arginine and histidine), the partner is an anion. Which anion depends on how the material was made and finished.

Why TFA is so common

Most synthetic peptides are made by solid-phase synthesis and cleaved from the resin with trifluoroacetic acid. They are then usually purified by reversed-phase HPLC, often with TFA in the mobile phase. After that step, peptides are usually delivered as TFA salts [1][2]. Acetate is a common alternative, but it needs an extra ion-exchange step, and TFA cannot be fully removed [3].

Why it changes the numbers on a report

A vial labeled 10 mg holds peptide, counterions, residual water and trace components. The share that is peptide is called net peptide content. A 100% pure peptide can still have a net content below 100%, especially when it has many basic residues [2].

HPLC purity is a ratio of the main peak area to the total peak area, measured by UV absorbance at about 210–220 nm. Water and salts are not detected by this method, and TFA is UV-inactive [2][3]. So purity alone does not show how much peptide a sample actually contains.

Where to look on a COA

  • Purity: the HPLC line, with method and wavelength. A peak-area ratio.
  • Content: a quantitation result in milligrams, compared with the labeled amount. Labs may use methods such as amino acid analysis or elemental analysis [2].
  • Water: a moisture line, commonly by Karl Fischer titration [3], if tested.
  • Counterion: a line naming the salt form or a result such as TFA or acetate content, if tested. Ion chromatography is one method used [3]. Many reports have no such line.
  • Identity: the mass spectrometry result. It confirms the molecule and says nothing about the salt form.

If a report does not state the counterion, that is a fair question for the testing lab or the seller. A missing line is a gap in the documentation, not evidence of a problem.

A worked example from a real report

The Epithalon 10 mg listing references report COA9240, issued by Bioviridian on September 13, 2026 for lot ET07072026. The report summary on the product page shows 99.87% purity by RP-HPLC at 214 nm, identity confirmed by LC-MS/MS, a molecular weight of 390.3 g/mol, and content of 10.11 mg against the 10 mg label. That summary does not name a counterion. Reading the report well means holding two ideas together: the purity line describes peak share, and the content line describes weight. These figures describe only that tested lot [4].

Limits

A COA describes the tested sample, not every vial. Content results depend on the quantitation method and its uncertainty, and batches differ. Counterion type is also one reason results for the same peptide may not be directly comparable between suppliers. None of this replaces a researcher’s own verification.

To check a report, match the lot number on the report to the vial label, then confirm the report on the lab’s own website. The COA library links every current report, and the guide on purity versus peptide content covers the other lines in more detail.

References

  1. Compound Brief, “TFA Salt vs. Acetate: Why the Counterion Matters” (October 2026). (Published by DAAVY.)
  2. Iris Biotech, “Net content and purity, two key parameters in peptide synthesis.” (Manufacturer technical page.)
  3. Bachem Knowledge Center, “Quality control of amino acids and peptides: a guide.”
  4. DAAVY Research, Epithalon 10 mg product page and COA9240 summary.

References 2 and 3 are manufacturer technical pages, not peer-reviewed articles.