For Research Use Only. Everything on this site is intended solely for laboratory, analytical, or institutional research — not for human or veterinary use, consumption, diagnosis, treatment, or prevention.

Analytical documentation guide

Molecular Weight on a COA: Why Mass Spec Shows Many Peaks

A certificate of analysis lists a molecular weight and an LC-MS identity result. This guide explains what those lines measure, why one peptide appears at several mass-to-charge values, and what a mass match does and does not establish. It is written for laboratory research documentation only.

4-minute readPublished by DAAVY Research

The short answer

The molecular weight is the mass of one molecule, not the weight of the powder.

A mass spectrometer measures ions by mass-to-charge ratio (m/z). Larger peptides usually carry several charges, so one compound shows up at several m/z values. Software converts that set of peaks into a single neutral mass, which is compared with the expected molecular weight. How much material is in the vial is a different line, reported as content.

What the molecular weight line means

The report for DRP-TR20 20 mg (COA7118) lists a molecular weight of 4813.5 g/mol. That is the expected mass of one molecule, in daltons per molecule or grams per mole. It does not say how much compound is in the vial. On the same report, identity is given by LC-MS/MS, purity by RP-HPLC, and content by HPLC quantitation, three separate questions with three separate lines.

Why one peptide shows several peaks

A mass spectrometer does not weigh molecules directly. In electrospray ionization, peptides and proteins usually pick up more than one proton, so a sample produces a distribution of charge states rather than a single ion (Huang and McLuckey, 2010). Siuzdak (1994) describes the relationship for protonated ions as Mr = (m/z × z) − z, where z is the number of charges. His worked example uses egg white lysozyme: m/z 1302.5 at z = 11 gives a molecular mass of about 14,317.

Rearranged, m/z is roughly (M + z × 1.007) divided by z. As an illustration only, a neutral mass of 4813.5 would appear near m/z 1204.4 at four charges, 963.7 at five and 803.3 at six. These are teaching calculations, not values read from any report.

What deconvolution does

Deconvolution is a method of transforming a multiply charged spectrum into an uncharged one, which lets the analyst calculate the molecular weight of the components (Agilent OpenLab documentation). When a COA says identity conforms, it generally means the deconvoluted mass agreed with the expected mass within the lab's stated tolerance. The tolerance is set by the lab, so it is reasonable to ask what it was.

Average mass versus monoisotopic mass

Large molecules contain many carbon atoms, and a small share of them are the heavier carbon-13 isotope. A lab may report an average mass or the mass of the lightest isotope combination, and the two can differ by more than a dalton for a molecule this size. A small gap between a listed weight and a measured one can therefore reflect the reporting convention alone. The report's method note should say which was used.

What a mass match does not establish

A matching mass supports identity, but it does not by itself show the amino acid sequence, because different molecules can share a mass. It does not show purity, which comes from the chromatographic result, and it does not show content. A report also describes one lot at one point in time. Check that the lot number and report number match the material in hand, and compare with the COA library. See also HPLC vs. LC-MS and purity vs. peptide content.

A short checklist for reading any COA

  1. Find the lab name, report number, lot number and report date.
  2. Locate identity, purity and content as three separate lines.
  3. Compare the listed molecular weight with the expected value for the compound.
  4. Check which mass convention (average or monoisotopic) and what tolerance the lab used.
  5. Confirm the report with the testing laboratory where that option exists.

Frequently asked questions

Is the molecular weight on a COA the weight of the product in the vial?

No. It is the mass of one molecule of the compound. The amount in the vial is reported separately as content.

Why does the mass spectrum show more than one peak for one compound?

Electrospray ionization typically gives peptides several charge states. Each appears at a different mass-to-charge value, and software combines them into one neutral mass.

Does an identity match prove the sample is pure?

No. Identity and purity are separate results from separate parts of the analysis.

References

  1. Siuzdak G. The emergence of mass spectrometry in biochemical research. Proc Natl Acad Sci USA 1994;91:11290–11297. Full text (Scripps)
  2. Huang T-Y, McLuckey SA. Gas-phase chemistry of multiply charged bioions in analytical mass spectrometry. Annu Rev Anal Chem 2010;3:365–385. PubMed Central author manuscript
  3. Agilent OpenLab, Data Analysis: Spectral Deconvolution. Documentation page
  4. DAAVY Research, DRP-TR20 20 mg listing and COA7118 summary (accessed November 8, 2026).

This overview was compiled from the cited references and published by DAAVY Research. It does not validate a particular laboratory method, report, sample, or lot. For laboratory research use only; not for human or veterinary use.